dehaze
Jerry Damson Acura
dehaze
Jerry Damson Acura

Acura Oil Change

What type of oil should I use?

Always use Acura Genuine Oil, available atJerry Damson Acura. When Acura Genuine oil is not available, it is very important to choose an oil displaying the “Starburst” certification symbol. This symbol indicates that the oil meets the latest performance requirements set by the automotive and oil industries. Oil bearing the Starburst will provide superior performance in the areas of deposit and sludge protection, wear protection, and oil life. These oils will also protect the environment by extending the life of your emissions system and conserving energy through better fuel economy.

Jerry Damson Acura recommends the use of Acura Genuine oil for your vehicle. This oil meets the Starburst performance requirements listed above, but is also subjected to a series of Acura specific tests to guarantee optimum performance and compatibility with your Acura vehicle.

Refer to your owner’s manual to determine the proper weight (viscosity) grade for your Acura. Your vehicle was designed to use this specific weight grade. Confirm that the weight listed on your oil’s label matches this recommendation exactly before using it in your engine.

What about synthetic motor oils?

You may use a synthetic motor oil if it meets the same requirements listed above. That is, it must display the Starburst symbol, and match the weight grade recommended in your owner’s manual.

When using synthetic oil, you must follow the oil and filter change intervals given in the maintenance schedule.

How often should I change my oil after the first service?

Refer to your owner’s manual for the recommended service intervals. Separate maintenance schedules are listed for “normal service” and “severe service.” Read the description of severe service carefully. Most vehicles will fall under the normal service category. Note that the service intervals are listed by time in addition to distance. Your oil should be changed at whichever interval, time or distance, occurs first.

There is absolutely no benefit in changing your oil more frequently than recommended in your owner’s manual. This will only increase your cost of ownership, and create an unnecessary burden upon the environment by increasing the amount of disposed oil.

Do not exceed the recommended maintenance interval. Oil eventually deteriorates and loses its ability to protect your engine, due to heat, friction, and exposure to exhaust components. Engine oil contains special additives to enhance the oil’s performance, and these additives are also broken down or consumed with distance and time. Engine damage can occur if the proper maintenance schedule is not followed.

What’s a “crush washer” and why is it important to my Acura?

As an Acura owner, the crush washer you should be most concerned with is the one that must be replaced every time you change your motor oil. This crush washer fits between your oil pan and the drain plug. It is a one-time-use washer. Discard the old washer at each oil change and replace with a new one. If you have your oil changed at any service outlet other than a Acura dealer, remind them of the importance to use a new crush washer.
When a new washer is installed and the drain plug is tightened, this washer “crushes” to form a very tight seal, thereby preventing motor oil leaks without overstressing the oil pan threads.

Oil changers who are not aware of its importance may think it’s OK to re-use this washer. Since it has already been crushed, it will not collapse further. As a result, the installer may over-tighten the drain plug to get a tight fit. This can eventually lead to stripped threads in the oil pan — a very expensive repair.

This is another example of why your Acura dealer is the easy choice for your service needs. Acura dealers know your Acura best.

Are there special steps I should follow when changing my oil filter?

When installing a new Acura oil filter, make sure you torque the filter to the proper specification. This way, you fully compress the filter’s O-ring so there are no leaks. Torque specifications are listed on the filter. Before you install a new oil filter, remember to inspect and clean the filter’s threads and O-ring surfaces. And to keep the new O-ring from shearing when you torque the filter, smear a little engine oil on it. If the O-ring from the old filter is stuck to the engine block, scrape it off thoroughly and wipe the surface clean. Never install a new oil filter with the old O-ring stuck to the block. The filter could come loose over time.

Call Us

Service: (888) 572-1864

Parts: (888) 572-1864

Service & Parts Hours

Monday - Friday 7:00 AM - 5:30 PM
Saturday 8:00 AM - 2:30 PM
Sunday Closed

Location

2402 Leeman Ferry Road, Huntsville, AL 35801
GET DIRECTIONS